- High-Build Polyaspartic Floor Coating
- 5kg Containers
- Two Pack
- Fast Curing
- UV Stable
- Colour Range Available
Elladur™ SF Clear is a high-build Polyaspartic/Polyurea type fast-cure floor coating system based on advanced materials, designed to provide a transparent tough and durable gloss finish to a range of floor surfaces. Elladur™ SF Clear is light stable and taint approved with good chemical resistance. Decorative and anti-slip finishes can also be created incorporating suitable flakes and aggregates.
Advantages
- Fast curing at low temperature
- High build
- Tough but flexible
- UV stable
- Ease of application
- Excellent high gloss finish
- Excellent adhesion
- Solvent-free
Recommended Use
- Where high build UV stable coatings are required
- Areas where a fast return to service is required
- Medical, Commercial and Industrial Floor areas
- Decorative floors
- Domestic areas
Surface Preparation
New Concrete Floors:
New concrete must be clean, sound, dry, fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm² is required.
Existing Concrete Floors: Remove all dirt, oil, grease, old paint or any other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing and making sure all residue of detergent is washed and removed by rinsing with clean water. Local repairs should be carried out using Resuscreed PA.
Existing Floors (previously coated):
All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. If the old resin flooring cannot be removed then please consult with our technical team for advice on intercoat adhesion and suitability, as it may not be compatible with the existing floor coating.
Where Elladur SF Clear is applied to masonry/concrete surfaces, care must be taken to ensure that surface preparation is thorough but does not disfigure the surface.
Priming
Open and porous substrates may require priming with Resuseal WB, also Resuprime ST may be used as primer on the dry substrates only with less than 75% ERH reading.
Where the Relative Humidity of a substrate exceeds 75% ERH please refer to the table below for required number of coats to achieve proper moisture tolerance.
ERH%Required Coating Thickness
75-85 1 coat of Resuprime MVT at 200 µm per coat
85-92 2 coats of Resuprime MVT at 200 µm per coat
92-97 3 coats of Resuprime MVT at 200 µm per coat
Application
Mixing: Mix the entire contents of the base with the hardener. If a separate mixing bucket is being used mix thoroughly ensuring all contents of both components are removed from the buckets supplied. Mix using a slow speed electric mixer for approximately two to three minutes until the two components are fully combined.
The mixed unit should be applied immediately by roller, brush or squeegee with a consistent procedure. Floor areas should be cross-rolled to ensure even application and to minimise roller marks.
Elladur™ SF Clear may be applied to an existing resin floor system where a primer is not required. When applied direct to porous substrates such as concrete the surface must be primed with Elladur™ SF Clear to ensure good adhesion to the surface
Application Conditions
The ambient temperatures of the areas should not be allowed to fall below 15°C throughout the application and the curing period, as this could have an adverse effect on the appearance and colour of the system. Surface temperature must be above 10°C. Where possible it is recommended that the application area is heated to a minimum temperature of 15°C ideally to allow the ambient and substrate temperature to stabilise prior to the installation.
Substrate Temperature: 2 - 30°C
Note: Use brushes or rubber squeegee to spread the coating and then back roll it if required to achieve proper coverage rate.
Relative Humidity up to 90%
In case of application at lower temperature, DO NOT store the material in cold conditions as it will affect the material viscosity and flow. Make sure materials are kept at specified storage condition prior to application.
Full product data sheets and safety data sheets are available on request.
Download Product Data Sheet (PDS_Elladur_SF.pdf)
Payment & Security
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.